Description

• Model: CC-PAIN01
• Brand: Honeywell
• Series: Experion Series C I/O
• Core Function: Acquires high-level 4–20 mA process signals
• Type: High-Level Analog Input Module
• Key Specs: 16 single-ended channels, 16-bit A/D, 50 ms scan rate
• HART: Not supported
• IOTA: CC-TAIN01 non-redundant / CC-TAIN11 redundant
• Associated Part Number: 51410069-175

Product Introduction

Honeywell CC-PAIN01 is a 16-channel High-Level Analog Input module for the Experion Series C I/O architecture. It accepts high-level current signals from 2-wire or self-powered transmitters, with a standard input range of 4–20 mA. Honeywell classifies it as the non-HART version of the Series C high-level analog input family.

The module uses a 16-bit A/D converter and scans its 16 single-ended channels in 50 ms. Its analog input is designed around a 200 Ω sampling resistor, with documented accuracy of ±0.075% of full scale at room temperature and ±0.15% across 0–60 °C. For a redundant installation, Honeywell specifies the CC-TAIN11 IOTA; the non-redundant arrangement uses CC-TAIN01.

Key Technical Specifications

Honeywell’s Series C specification identifies CC-PAIN01 as a 16-channel high-level analog input module and documents its 4–20 mA input, conversion resolution, scan rate, accuracy, and IOTA combinations.

Honeywell CC-PAIN01

Application and Selection Notes

This module is aimed at conventional 4–20 mA process transmitters. Typical signals include pressure, flow, level, temperature transmitters with current outputs, and other continuously measured process variables.

The key distinction is that it is non-HART. Honeywell’s Series C documentation separately identifies CC-PAIH51 as the 16-channel HART analog input module, while CC-PAIN01 belongs to the non-HART AI-HL group.

That difference affects procurement. A transmitter may produce the same 4–20 mA signal on both systems, but HART configuration and diagnostics are not available through this module. If the plant relies on online HART communication, the I/O selection needs to reflect that requirement.

I would also verify the IOTA before ordering. CC-TAIN01 is the 6-inch non-redundant option, while CC-TAIN11 is the 12-inch redundant option.

Advantages and Limitations

Advantages

• 16 analog channels in one Series C module.
• Standard 4–20 mA transmitter interface.
• 16-bit signal conversion.
• 50 ms input scan.
• Non-incendive field-power capability.
• Supports non-redundant and redundant IOTA arrangements.

Limitations

• No HART communication.
• No voltage-input mode.
• No differential input capability.
• Requires the correct Series C IOTA and system configuration.
• Not a direct functional substitute for HART-enabled analog input hardware when HART data is required.

Quality Inspection and Pre-Shipment Checks

1. Incoming inspection: Verify Honeywell markings, model number, associated part number, serial number, connectors, PCB condition, and signs of corrosion or prior repair.
2. Live test: On a compatible Series C test setup, check startup diagnostics, module recognition, representative 4–20 mA input acquisition, channel status, and alarm behavior. Record the results in a Test Report.
3. Electrical checks: Verify connector continuity, grounding, supply paths, and applicable isolation characteristics according to the approved procedure.
4. Configuration verification: Record the IOTA type, channel mapping, hardware revision, and installed system configuration.
5. Final QC: Photograph the identification label, use ESD-safe packaging, add mechanical cushioning, and retain the QC record.

Test photos and available Test Reports can be provided with the shipment when requested.

Technical Replacement Risks

HART mismatch. CC-PAIN01 is a non-HART module. Replacing a HART-enabled input module with this unit may preserve the basic current signal but remove HART functionality.

IOTA mismatch. The non-redundant and redundant installations use different IOTAs. Confirm the existing architecture before moving the module.

Wrong signal type. This hardware is intended for 4–20 mA current input. It should not be selected for voltage or differential analog signals.

Firmware and system revision. The hardware must be compatible with the installed Experion Series C configuration. Record the existing hardware identity before replacement.

And take a wiring photo first. It is a very cheap form of commissioning insurance.

Purchase and Logistics Notes

For international procurement, use a description such as Honeywell CC-PAIN01 Experion Series C 16-Channel Non-HART Analog Input Module. Commercial records commonly associate the module with part number 51410069-175.

State the actual condition separately:

• New Original
• New Surplus
• Refurbished
• Repaired

The purchase order should include the complete model, part number, hardware revision where available, IOTA type, functional-test status, warranty, country of origin, and package data.

For export shipping, protect the module with ESD-safe material, rigid cushioning, and moisture protection appropriate to the route. Keep the part number consistent across the commercial invoice, packing list, and physical label.

Quick Conclusion

• CC-PAIN01 is a 16-channel non-HART High-Level Analog Input module for Honeywell Experion Series C.
• It accepts 4–20 mA signals from 2-wire or self-powered transmitters.
• The module provides 16-bit A/D conversion and a 50 ms input scan rate.
• CC-TAIN01 is the documented non-redundant IOTA, while CC-TAIN11 is used for redundant installation.
• It should not be selected where HART communication is required.

FAQ

What is Honeywell CC-PAIN01?

It is a 16-channel High-Level Analog Input module for the Experion Series C I/O system, designed for 4–20 mA process signals.

Does CC-PAIN01 support HART?

No. Honeywell classifies CC-PAIN01 as the non-HART AI-HL module.

How many channels does it provide?

It provides 16 single-ended analog input channels.

What input signal does it accept?

The published specification gives a 4–20 mA current input for 2-wire or self-powered transmitters.

Which IOTA is used with it?

Honeywell lists CC-TAIN01 for non-redundant installations and CC-TAIN11 for redundant installations.

Is 51410069-175 related to CC-PAIN01?

Yes. Current spare-parts records associate 51410069-175 with CC-PAIN01. Actual stock should still be checked for revision and configuration.